[ 已解决 ] 不支持硬件平台 x86_64 和引导加载器 grub2-efi 的组合?

[血族使天]

前两天主板坏了，修好后准备吧 openSUSE 重装一下，我的主板是 UEFI 的，之前安装的时候使用的是 grub2-efi 引导系统，结果这次发现默认引导变成了 grub2，如果手动改回 grub2-efi 的话会提示：

 不支持硬件平台 x86_64 和引导加载器 grub2-efi 的组合 

因为我的主板如果使用 grub 引导的话貌似会不识别，所以只能用 efi 引导。
有解决办法吗

[marguerite]

YaST 一般是不会错的。你的新主板还是 UEFI？

[gmg137]

主板被修电脑的给调包了吧！

[血族使天]

晕，怎么可能，连序列号都没有变。。。我是 UEFI，以前都是没问题的，不知道为什么突然就这样了

[gmg137]

会不会是在 UEFI 的设置中需要先解锁什么的？或者你先试试用 GRUB2 引导，如果成功了那就说明你主板被调包了，嘻嘻！，，，总之我听说过修电脑偷换硬盘的，把好的换成坏的。

[marguerite]

在我的翻译存档里找了下，原文是这个：

unsupported combination of hardware platform x86_64 and bootloader grub2-efi

可以自己 google 看看。

[marguerite]

randombio.com/linuxsetup135.html UEFI UEFI created major problems for Opensuse 13.1. After eight attempts at installation, we finally discovered the trick by trial and error. Elilo No longer supported, even though it’s still in the menu. Grub Got the message: “An error occurred during initrd creation” but it tried to boot anyway and got stuck on a gray text-mode grub> prompt. Grub2 Same thing Grub2-EFI Got the message “Unsupported combination of hardware platform x86_64 and boot loader grub2-efi.” on the top installation screen. In red this time. Selecting Secure Boot had no effect. Despite the red warning message, Opensuse lets you proceed, and you end up yanking the power cable once again. But in fact, Grub2-EFI is the only one that works. There’s just a trick you need to go through before you can select it. Install grub2, selecting boot from MBR instead of the default root partition. The grub boot screen should then show a menu with 3 options: Installation Rescue system Check installation media So it still won’t boot up at this point. But if you select New Installation at this point, it now becomes possible to select grub2-efi and check Enable Secure Boot Support. The red error message was no longer present, and Opensuse successfully created a bootable hard drive. At boot-up, Grub finally gave Opensuse as an item in a green menu. This means OpenSuse 13.1 is actually able to boot up properly. Success.

让我想起来这似乎是 ISO 的一个 bug。不过 ISO 的 bug 在 ISO 发出来之后就 wontfix 了。除了上面那种方法，你也可以用 Factory 或者 13.2 beta 的 ISO 来写 grub2-efi。

[血族使天]

好吧，我已经无言面对江东父老了，蓦然想起是不是我 UEFI 设置有问题，结果进去一看，发现安全启动是打开的，顿时泪流满面啊。